Products

 

Have a question? Call.

(866) 573-9104 / (760) 930-9400

Get Covered with an Extended Warranty

Extended warranty coverage limits unexpected repair bills and protects your new laboratory equipment purchase.

Contact Us.

WaferPlate™ Model HP90 Fully Programmable Digital Bake Plate

Designed Specifically for Baking Silicon Wafers

Large circular milled-flat aluminum surface with temperature uniformity better than 1% across the heating surface. Designed specifically for working with 12” (304.8mm) diameter or smaller silicon wafers and other samples where temperature accuracy and surface uniformity are a must.

HP90 $3,500.00

Features

  • 13.875 in (354.24 mm) diameter heater surface.
  • Milled flat plate aluminum ideal for 12 in (304.8 mm) or smaller silicon wafers
  • Controllable remotely from a PC or industrial controller via RS232 I/O port with full access to all parameters or data
  • Bench top controllable and programmable using the remote controller provided
  • Temperature range from room temperature to 350 °C
  • Readable and settable to 1 °C
  • Accuracy 1% of setting
  • Uniformity of temperature from the middle of the plate surface to within 0.75 in of the sides is better than 1%
  • Temperature stability ± 1 °C
  • Calibrated to 0.1 °C for guaranteed accuracy
  • Remote controller enables storing 5 individual programs with up to 10 steps per program for a variety of hands-off, repeatable sample runs
  • Programs automatically repeatable from 1 to 99 times or infinitely if wanted
  • Ramp temperatures up or down at 1 °C/hour increments from 1 °C to 450 °C
  • 1500 W heater power
  • Unique temperature indicator lighting ring at the bottom sides of chassis. Colors change from blue (no target temperature) to yellow (when heating below 50 °C) to red (when heating above 50 °C). The lights will flash until the temperature is stable within ± 0.2 °C
  • Built-in count down timer with audible alarm and settable Auto-Off
  • 12-month warranty
  • UL, CSA and CE approvals pending

Product Description:

The Torrey Pines Scientific WaferPlate™ Programmable Bake Plate is a fully programmable digital hot plate designed specifically for baking silicon wafers. In manual operation simply set a target temperature and the unit will go to and hold that exact temperature to within ± 1 °C. In the programmable mode routines can be stored in memory for instant recall and use. The stored routine will be run automatically, and exactly the same, again and again.

Programs can be simple or complex depending upon need. Multiple temperatures, temperature ramp rates if wanted, and dwell times can be stored. These programs can be written and stored in the remote controller provided with the unit, or the programs can be as simple or complex as needed when written by the user on a PC and run by that PC via the RS232 I/O port on the rear of the heater.

Product Specification:

Temperature Measurement
Platinum RTD 100 Ω at zero mounted in the heater top
Range 10 °C to 350 °C on the plate surface
Readability
Hot Plate
Dimensions 13.875 in (352.4 mm)
Maximum plate temperature 350 °C
Temperature control type PID
Temperature stability 1 °C
Heater power 1500 W
Temperature Uniformity Better than 1% of setting from center to within 0.75” of plate edge
Electrical
Available 100, 115, and 230 VAC, 50/60 Hz
Fused Yes
Line Cord Detachable, 6 ft (1.8 m), 3-wire grounded. Single phase
Dimensions
Unpacked (Heater Module)
Width 13.875 in (352.4 mm) circle
Height 5.75 in (146 mm)
Weight 21.5 lb (9.54 kg)
Unpacked (Control Module)
Width 5 in (127 mm)
Depth 2.5 in (63.5 mm)
Height 4 in (101.6 mm)
Weight 1.5 lb (0.54 kg)


  

Additional Images (click to enlarge)